Sampling Equipment and Media
AAC can provide a full range of media to meet your sampling needs.
A partial list of the media we can provide is listed below.
We have a large inventory of 6 Liter and 1.4 Liter canisters pre-cleaned and either batch or individually certified depending on your sampling needs. We have several varieties of canisters available for different applications including Restek TO-cansTM for low-level ambient toxics and ozone precursors monitoring as well as Restek SilcoCanTM and Entech SiloniteTM Canisters for ultra inert sampling needs including speciated sulfur compounds. Canisters can be certified to meet EPA TO-15 SCAN or low-level SIM requirements.
We have a variety of sizes of high-pressure sample cylinders available that are pre-cleaned and either batch or individually certified depending on your sampling needs. These cylinders can be used for an array of applications including LNG, LPG, Biogas, fixed gases analysis, BTU analysis, neat gas analysis, sulfur compounds analysis, etc.
Tedlar and Teflon Bags
We can supply Tedlar or Teflon bags upon request.
Vost, Tenax, Charcoal, Silica Gel, Chromosorb, and other Sampling Tubes
A variety of sampling tubes can be provided upon request.
We have a full supply of pre-cleaned flow controllers available for our Summa® canisters for fill times ranging from 15 minutes to 24 hours. All flow controllers are set prior to use with a digital calibration device accurate to 0.1mL/min. Flow controllers can be provided individually certified and paired to a specific canister for either EPA TO-15 SCAN or low-level SIM requirements. Both end-of-line and inline stainless steel filters can be provided to meet your sampling needs. We can custom build stainless steel sampling lines to meet your requirements.
We can build a variety of custom hydrocarbon samplers to meet your indoor, outdoor and stack testing needs. Samplers can be provided to supply a purge or sweep volume from a clean source for vapor intrusion or other needs.
We can provide pre-assembled SCAQMD 25.1 and EPA 25 sampling trains in Heavy Duty Aluminum Boxes. Each box contains two identical sampling trains for the method required duplicate sample. Each sampling train consists of a 6 Liter Summa@ canister, a pre-attached flow controller, and a stainless steel trap (25.1) along with all necessary connections, plugs, filters, and instructions. The flow controllers are pre-cleaned and typically adjusted for a one hour sampling event. Other flow rates can be custom ordered to fulfill your project needs. All you have to do is add dry ice and you’re ready to sample!
We can provide pre-assembled SCAQMD 25.3 sampling trains in Heavy Duty Aluminum Boxes. Each box contains two identical sampling trains for the method required duplicate sample. Each sampling train consists of a 6 Liter Summa@ canister, a pre-attached flow controller, and a water impinger (25.3) along with all necessary connections, plugs, filters, and instructions. The flow controllers are pre-cleaned and typically adjusted for a one hour sampling event. Other flow rates can be custom ordered to fulfill your project needs. All you have to do is add ice and you’re ready to sample!
Sampling Trains in Heavy Duty Aluminum Boxes
DNPH Carbonyl Sampling Cartridges
We can supply DNPH cartridges for sampling and analysis by EPA TO-11A, IP-6A and other methods. We can pre-certify the cartridges as needed. We can also coat specialty cartridges to meet your sampling needs and provide a variety of ozone-scrubber devices
DNPH Coated Filters and Passive Samplers
We offer DNPH coated filters and passive samplers for sampling and analysis by EPA IP-6C and other methods. We provide pre-coated and certified DNPH filters pre-installed in a variety of passive samplers including GMD and SKC badges.
Wet Sampling
AAC can provide a large variety of sampling and spiking solutions, impingers and vials and other accessories to accommodate your wet sampling needs.
A partial list of what we provide is included below.
- Sampling Solutions
- DNPH solutions for sampling and analysis by EPA-0011 and CARB 430/430M methods – All of our sampling solutions are pre-certified and shipped overnight on ice to you to maintain their integrity. We can provide a modified DNPH solution for Acrolein sampling (CARB 430M) that has been proven to minimize the breakdown of Acrolein in acidified DNPH solutions.
- BHA solutions for sampling and analysis by NCASI method 105.01.
- EPA CTM-027 solutions for ammonia sampling and analysis.
- A modified CTM-027 solution for speciated amines sampling and analysis developed by AAC
- EPA TO-8 NaOH solution for Phenol and Cresols analysis.
- EPA 26/26A acidic and basic solutions.
- Spiking Solutions for field use for CARB 430/430M, EPA-0011, NCASI 99.02, 105.01 and other methods.
- We provide accurate pre and post sampling weighing for all types of filters including quartz and glass fiber 8x10 filters for TSP or PM10 HI-VOL sampling..
- Precoated solutions and filters for Isocyanate Sampling.
- Midget 20mL glass impinger sampling trains for CARB 430/430M and other methods.
